Turbo Mills of Magnesium Sulfate

Turbo Mills of MAGNESIμm SULFATE This product technology has been widely valued by the industry. The grinding mechanism of Turbo Mills of Magnesium Sulfate is mainly used to determine its wide range of applications, high fine, typical materials: super hard diamond, silicon carbide, metal powder, high purity requirements: ceramic pigment, medicine, biochemistry, medicine. Turbo Mills of Magnesium Sulfate can convert a normal gas from a gas source to an inert gas such as nitrogen, carbon dioxide, is an inert gas protection device, which is suitable for smashing, grading, and processing of flammable explosive, oxidative materials.

In terms of airflow milling, it is important to understand its operational rules, which is very important because only familiarize the procedure, can operate correctly.
1. The operation rules of Turbo Mills of Magnesium Sulfate are as follows: Prepare materials after the preparation before the boot is received. Complete the site to clean the grocery. Check whether the transportation pipes and auxiliary equipment, whether the pipelines are blocked, leak or poor sealing, whether the auxiliary equipment is intact, whether it works normally. Whether there is a phenomenon that the material is accumulated in the outer casing and the separator, if the accumulated material is required. Whether the bearing is lubricated, whether it is lubricated in an appropriate place. Check if all pipes, fastening bolts, washers, spindles, and instruments are intact, normal and flexible.
Second, Turbo Mills Of Magnesium Sulfate starts the motor, control the current and time at starting, so that the device can start running. When the equipment is operating normally, the feed speed can be adjusted according to the properties of the material. Uniform continuous feed should not be large or small, thereby affecting the separation effect of the grinding machine, making the machine easily malfunction. During operation, if an abnormality occurs, stop checking immediately before the failure continues.
Third, the main procedures of Turbo Mills of Magnesium Sulfate are as follows: After the material in the grinding machine is completely pulverized, it should stop the input and turn off the motor. After the machine is idling for 3 minutes, press the stop button to stop the machine. When the machine is completely stopped, open the check door and check the wear of the vessel. Fill in the corresponding production record, update the device status flag, which is convenient for the next use.


ALPA cobaltate Turbo Mills of Magnesium Sulfate Case Sharing: Beijing Lithium Electric Materials Company purchased a Turbo Mills of Magnesium Sulfate from our AlPa in 2020. Ultrafine powder for lithium cobaltateCrusher, the company has three particle size requirements for lithium cobaltate, which requires a device to be satisfied. In response to the company's unique needs, our ALPA engineers have finally been targeted to customize a Turbo Mills of Magnesium Sulfate. The pulverizer can meet the production requirements of multiple particle size sections, equipped with subsequent airflow classifier systems, and can be sorted by different particle size products.
Technical parameters:
Finished particle size: lithium cobaltate small particles D50: 3-6 μm; lithium cobaltate large particles: 50: 8-20 μm; Trimetimeterials D50: 6-13μm;

The causes of vibration and solutions can be conducted from the following aspects:
1 Hammer installation error in maintenance assembly. When the hammer is turned off, in order to prevent the weight of the rotor from losing balance, all the hammers in the pulverizer must be turned out together, otherwise it will have a strong vibration in the operation.
2, the difference between the weight of the two sets of hammer exceeds 5 grams. The method of excluding is to adjust the weight of the hammer, so that the difference between the two sets of weight is less than 5 grams.
3, individual hammer card is too tight, there is no open in operation. After the stop, turn the observation with hand and find a way to turn the hammer flexible.

5, the spindle bending deformation. The solution is to school straight or replacement.
6, the bearing gap exceeds damage. It is generally used to solve the problem.
7. The bottom angle fixing nut is not fixed in a fixed or running. The solution is tightening.

ALPA Technology recommends that you should pay attention to the performance of the equipment during the use of ultrafine airflow classifiers, jet grading machines, powder classifiers.