Hammer Grinder of Poly

With the continuous advancement of crusher technology, Hammer Grinder of Poly has been familiar with people. Now the most popular crushing equipment is Hammer Grinder of Poly. It has a wide variety, available for laboratory, home and factory use. It has a wide range of production, high energy consumption, high automation, and high classification quality.

The following is a detailed description:

1. Feeding granularity control

Most Hammer Grinder of Poly has a certain upper limit requirement for feed particle size. After entering the pulverization cavity, it can be sufficiently accelerated before collision and crushing with other particles. It is difficult to completely accelerate after large particles enter the pulverized cavity, which will allow them to stay in the machine too long, resulting in too high energy consumption. Therefore, in large-scale production of ultrafine powder, it is an effective way to pre-ground the raw material of the particle size is an effective pathway for energy saving.
2. Working medium

Currently, the working medium of Hammer Grinder of Poly is mainly compressed air, superheated steam, inert gas, and the like. The choice of working fluid has a certain impact on crushing effects and economics. Superheated steam is superior to air in fluidity and critical flow rates to achieve higher flow rates and uniform flow fields. However, using superheated steam as a working fluid, it must be ensured that it is still in an overheating state before entering the product capture device, otherwise the material is condensed.
3. Feeding speed

Feeding speed is an important parameter reflecting gas flow grinding production capacity. During the pulverization process, the optimum ratio of the intake flow rate and the feed speed is the key to improving the crushing efficiency. In general, under certain intake flow conditions, the feed speed is proportional to the particle size of the product. However, the feeding speed is too fast, which will increase the particle density, mutual interference, disadvantage of the particles, and difficult to achieve the sufficient and effective collision between particles, affect the crushing effect; although the feed speed is too slow, the particles stay in the crush area The time can be extended, which will reduce the particle density, reduce the collision rate, resulting in a decrease in production capacity and an increase in unit production energy consumption.
4. Granular limit

Hammer grinder of poly during pulverization, as the material particle size decreases, the crystallization and intensity of the material increases. After reaching a certain degree, the particle size of the material is no longer reduced or reduced, that is, the crushing limit of the material is reached. At this time, the surface area of \u200b\u200bthe material increases, the surface activity of particles increases, and the particle agglomeration and grinding are in a dynamic balance, even if the grinding time is extended, it is difficult to further reduceSmall material particle size.


ALPA Carbon Hammer Grinder Of Poly Case Sharing: The company produces superfine and super fine pulveruts in the production of static pressure graphite. After multi-party investigation and experiment, finally selected our AlPA as a cooperative customer, we provide the Hammer Grinder of Poly provided to its Hammer Grinder of Poly, which is required for carbon crushing particle size, particle size range, yield and other needs.
Technical parameters:
finished particle size: D65: 200 mesh
Production capacity: 800-1000kg

Super Hammer Grinder of Poly is the use of air separation, heavy polishing, cutting Sliced \u200b\u200bforms to achieve ultra-smash of dry materials, extensive applications in various industries. Let's take a brief introduction to its daily maintenance content.
1, when the bearing oil is high, it is necessary to stop checking the cause of the fault and removal immediately.
2, easy to wear parts should pay attention to the degree of wear, pay attention to and do the preparation for replacement of parts.
3, for the top surface of the chassis of the active device, it is necessary to remove dust and other debris avoiding the machine that cannot be broken, the active bearing cannot move on the chassis, causing an accident.

5, the sleeper installed is easy to loosen, and it must be checked frequently.
6. Note that the operation of each part of the machine is normal.
7. If the rotating gear is in operation, if there is a hitting sound, it should be stopped in time and remove the fault.

ALPA is a manufacturer dedicated to powder grading machine, precision classifier, laboratory grade machine, and we have years of production experience in the production of products, while in many mechanical products We also have achieved a lot of important breakthroughs in the field, and believe that you will be the primary choice for your product purchase.