FL/ITC Multiple Classify Wheel Classifier for Xanthan gum

We all know that FL / ITC Multiple Classify Wheel Classifier for Xanthan GUM is a strong airflow pulverizer, and many stubborn hard materials have been cut into a uniform block,

FL / ITC Multiple Classify Wheel Classifier for Xanthan GUM is mainly used for more refined materials. The fractional particle size is 1.5 to 0.005 mm, and the crude material is sieved. The principle of pulverization is substantially the same as the hydraulic level, and the above settlement theory can also be used for airflow classification. However, in the airflow classification, since the density and viscosity of the air are much smaller than the density and viscosity of water, the same particles are more settled in the air than in the water. Moreover, the density and viscosity of the air vary with temperature and pressure. In order to cause air flow, wind grading equipment typically requires an appropriate fan (exhaust or blast). When the airflow is classified, the fine particles are usually taken away by the airflow. In some cases, the feedstock is sent to the grading device with the airflow. It is well known that the load of solid particles in the air under normal pressure does not exceed 500 g / m3 air. When it reaches 1 kg / m3, the particles fall from the airflow. The load is related to the density and particle size of the particles. When the fine particle material is treated, the load generally does not exceed 200 to 300 g / 3 air. According to this calculation, the volume concentration in the gas stream is much smaller than 0.03. Therefore, when the airflow is classified, in most cases, it belongs to the free settlement. The speed required to move the particulate material in the horizontal and vertical directions is relatively large, and the speed required in the horizontal direction is relatively large, and as the particle density increases, for example, for puls with a density of 1.5. Gram / cubic centimeter. The minimum wind speed is 2 m / sec; a powder material having a density of 2.5 g / cm, the speed is not less than 3.5 m / sec; a powder having a density of 4 g / cm 3, a minimum speed of 4 meters per second. Due to the complexity of the situation, the appropriate airflow rate in each particular situation should be determined by experiments. In the rising airflow, the water flow rate required to suspend a certain density and particle size is greater than the calculated value of the free settling, which is due to the uneven distribution of the airflow along the graded chamber portion. FL / ITC MULTIPLE Classify Wheel Classifier for Xanthan gum grade has a wide range of high classification efficiency, high classification accuracy, accurate cutting size, and good stability.

FL / ITC Multiple Classify Wheel Classifier for Xanthan gum works: qualified powder is conveyed to the upper portion of the crushing apparatus through the updraft classifier. The classifier classifies the qualified material and enters the cyclone collector (if a product having several particle size is required, add a plurality of vertical turbine grace machines). Fine tails are delivered to the bag dust collector via airflow. After filtration, the tail enters the exit of the lower part of the filter and empty the air. Main components of this unit: classifying machine, grinding, grading, synchronous completion, adjusting the speed of the classifier by frequency conversion speed, can adjust the product fineness. For example, if a machining process requires a number of granular sections of the product, then two to four can be increased on the basis of a standard classifier, so that the machine becomes a "two five" machines.

FL / ITC Multiple Classify Wheel Classifier for Xanthan gum after long-term use, it is necessary to clean the air mill. After cleaning the pulverizer, all machines must be removed. The demolition skill is also very good. When cleaning, the power supply can be turned off, and the remaining dust can be removed directly with a brush. We must remember to clean it layer by layer. When the displacement is disassembled, the four screws on the base can be removed, and then remove the hopper. When the screen is removed, the airflow pulverizer door can be opened directly and the screen can be removed at the end. After the mobile gear is removed, the fastening nut is released first, and then the live teeth are separated from the spindle. Then move the mobile gear and put it safely. Remove the fixed gear, remove the screw and remove the fixed gear. Be careful when disassembling the gas flow crusher. Do not cause any damage to the components of the machine itself.

ALPA Technology Co., Ltd. developed super fine classification machine, precision classifier, etc., can effectively protect the purity and accuracy of grading products, if you need to purchase related equipment, please feel free to contact us. .