FL/ITC Single Classify Wheel Classifier for Silicon nitride

With the continuous increase in social needs, FL / ITC Single Classify Wheel Classifier for Silicon Nitride is constantly improving with performance, finished product quality, service life, etc. It has also been widely used in many fields such as chemical, food, pesticides, cosmetics, dyes, coatings, and electrons.

Many manufacturers who want to make a crushing process will choose to buy a FL / ITC Single Classify Wheel Classifier for Silicon Nitride, but not all crushers can apply production and processing, erroneous processing methods will make crushing The speed of the machine shifts. The wear of the pulverizer is too fast, and the inner cavity of the pulverizer of the comparison should be used when the material hardness is too large. The equipment operates for a long time in a higher crushing pressure, which requires uniformity of cyclical replacement loss. The products after the crushing products are generally single peaks. If there is a double-peak or peak main reason, the pulverization pressure is unstable. The solution is based on the gas supply of gas source equipment to meet the amount of gas required for work, ensuring that the lowest air supply pressure of the gas is high than the working pressure. The feed speed is unstable. Solution to check if there is a blockage at the feed valve; the material is not very viscous, uniform in liquidity, and the stable control feed speed. The filter cake is formed in the pulverizer chamber. The solution is suspended, and the filter cake in the pulverizer chamber will then restore production.

Fl / ITC Single Classify Wheel Classifier for Silicon Nitride Work: Airflow Crusher and Cyclone Separator Drain Machine into a complete crushing system, compressed air is filtered and dried, then through the Lavar nozzle A plurality of high-pressure air interchange enters the crushing room at high speed. stream. The material is repeated collision, friction and shear, and the pulverized material is pulverized in the fan pumping force. Under the action of the high-speed rotary classifier, the fine particles that satisfy the particle size required by the grading wheel with the thickness and fine product separation into a t-cyclonic separator and dust collector by the grading wheel with the thickness, fine particles required to satisfy the particle size. Particles and continue to break in the crush region. High pressure gas injected around the crushing roomThe high-speed air flow consisting of solid particles injected into the crushing chamber is sprayed from different angles, and the solid particles collide with each other in the mixed airflow. change.

Do you know how to correctly use FL / ITC Single Classify Wheel Classifier for Silicon Nitride? I hope the content below can help you. 1. Preparation before the comminution is started to check whether the host, joint, pipeline, and the valve are normal, working properly. 2, open the pulverizer (1) Open the compressor power supply, dustpress pressure valve and the main valve, open the power switch of the pulverizer, turn on the power switch. (2) From zero, gradually adjust to the specified speed. (3) Open the fan, cyclone separator, dust removal and charger power, open the total power box, set the frequency of the inverter, and then start charging. (4) The particle size of the finished product can be adjusted according to the frequency and bearing capacity of the grading wheel. 3, pulverizer shutdown is: inverter - feeder - main valve compressor - compressive type impeller motor - cyclone material, dust removal switch - fan - universal power supply air compressor. 4, eddy current pulverizer maintenance (1) Regularly lubricate eddy current crushing machine, but the lubricant should not be too large to prevent the bearing temperature too high. (2) Check the wear of the impeller, screw conveyor and the crushing nozzle. (3) After pulverizing the material, the rubber powder should be removed to avoid clogging, thereby affecting the crushing effect. (4) After a filter bag, the vortex pulverizer is filtered, and it should be cleaned or replaced. 5, Eddy Current Crusher Precautions (1) When the discharge equipment is running, the unloading port cannot be reached, and the accident occurs. (2) The rotational speed of the impeller should not exceed the specified requirements, otherwise the temperature is too high, the impeller and the electric chance are damaged. (3) Regularly check the safety valve to ensure safety.

The above is the use of the FL / ITC Single Classify Wheel Classifier for Silicon Nitride, you can pay more attention to our friends who want to understand other crushers!